采购商用车CUBING检具系统 参数 图 查看采购商

大宗采购 | 2020-08-26

采购信息内容

采购商用车CUBING检具系统，我们需要承接方：设计、制作、安调，国内使用，商用车 总装车间 北京，我这是东风设计院的。        湖北 十堰

CUBING检具系统：Checking Fixture Cubing System：
1.部件信息 Component Information
1)产品相关参数 Product related parameters
图1

产品的外形尺寸-约2450x440x1200毫米。Overall dimension of product –
Approximate 2450x440x1200 mm.
2）分解图 Explosive view.
图2 3

2.工作过程：work process:
图4

前端模块检查夹具主要用于实际检查和匹配。
The front-end module inspection fixture is mainly used for actual inspection and
matching.
进行部分产品设计和工艺验证。
Carry out partial product design and process verification.
识别产品设计和过程中的零件对零件的配合问题和质量问题。
Identify the part-to-part fit and quality problems in product design and process.
提供一种持续的方法，用于对最新的前端模块组件进行预验证。
Provide a continuous method for pre-verification of the latest front-end module
components.
根据需要，对主量规上的零件更改或更正进行评估，以验证零件的配合。
As needed, evaluate the part changes or corrections on the master gauge to verify
the fit of the parts.
用于诊断产品设计、质量问题、过程问题和优化零件匹配的工具。
Tools for diagnosing product design, quality issues, process issues and
optimizing part matching.
旨在评估前端模块组件是否匹配和完成。
Aim to evaluate whether the front-end module components are matched and
completed.
确定问题的根本原因，在匹配的情况下，哪些部分将被修改。
Determine the root cause of the problem and in the case of a match, which parts
will be modified.
建立统一的流程和标准，验证新车型的功能外观。
Establish unified procedures and standards to verify the functional appearance of
new models.
名义公称值或单元检查夹具将用于评估零件。
The nominal value or unit check fixture will be used to evaluate the part.
3) 技术说明 Technical Description
基准和特性要与安装意图一致。
Benchmarks and characteristics should be consistent with the installation intent.
测量点遵循 CCP 和工艺要求。The measurement points follow CCP and
process requirements.
用于评价零件和其与周围零件的匹配关系，的零件能在类似总装条件下无
故障地安装和拆卸。与零件匹配的相关匹配区域要局部或全部做出，连接处宽
度大于 100mm。
Used to evaluate parts and their matching relationship with surrounding parts, the
parts can be installed and disassembled without failure under similar general assembly
conditions. The relevant matching area matching the part should be made partially or
completely, and the width of the joint should be greater than 100 mm.
保证零件的正常安装，及相邻零件的位置关系，待测零件安装及拆装后，
不能损坏或者划伤主检具。
Ensure the normal installation of parts and the positional relationship of adjacent
parts. After the parts to be tested are installed and disassembled, the main inspection
tool cannot be damaged or scratched.
零件安装方便，零件在检具上能够体现其安装在整车上的功能，满足其技
术要求， 能够和生产零件替换使用，保证可拆卸，以便于独立的评价分析某些
特定零件。
The parts are easy to install. The parts can reflect its function of installing on the
whole vehicle on the inspection tool, meet their technical requirements, can be
replaced with production parts, and ensure that they can be disassembled to facilitate
independent evaluation and analysis of certain specific parts.
要求主检具型面部分耐磨、不变形。
The surface of the main inspection tool is required to be wear-resistant and not
deformed.
功能主检具要满足测量要求，即保证每个检具模块功能区域用测量机能够
进行检测。
The functional main inspection tool must meet the measurement requirements,
that is, to ensure that the functional area of each inspection tool module can be
detected by the measuring machine.
零件本身功能主检具尽可能保证加工基准和测量基准一致。